Just How to Set up a Tub
Just How to Set up a Tub
Blog Article
Are you on the lookout for related information on Installing A Bathtub?
Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough job. If the old tub is easily accessible, the project can relocate immediately; if you need to open a wall to get rid of the old tub as well as position the brand-new tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will require an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the work as well as are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This short article will aid you mount a new bath tub in your shower room if you have currently purchased a brand-new tub and also don't need to change the plan of your previous supply of water pipes.
Your tools and material list ought to make up the following:
Preparing for the Setup
First of all, the supporting structure provided with the bath must be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its final setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome due to the restricted gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are valuable in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system and inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and the normal outlet for leakages.
Ultimately, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and securing around the tub ought to wait till the tub has been used at the very least once as this will resolve it into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washing machines remain in place in between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind ought to be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface between the bathroom and also the tiling, leading to issues with wetness and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that report about How to Install a Bathtub Yourself through an associate on another domain. Loved our blog entry? Please share it. Help somebody else locate it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Appointment
Report this page